Site Overlay


61F-GPN2 AC from OMRON >> Specification: Liquid Level Controller, 61F- GP-N2 Series, Conductive, Vac, W, 80 ms. Find great deals for Omron 61F-GP-N2 Processor/Controller. Shop with confidence on eBay!. The 61F-GP-N2-AC is a Conductive Level Controller for automatic water supply and drainage control. Compact plug-in controller for single or two-point.

Author: Vudojora Faukinos
Country: Algeria
Language: English (Spanish)
Genre: Science
Published (Last): 17 July 2008
Pages: 251
PDF File Size: 5.47 Mb
ePub File Size: 7.37 Mb
ISBN: 979-3-99950-738-9
Downloads: 70879
Price: Free* [*Free Regsitration Required]
Uploader: Meztikree

If the sufficient omrron cannot be provided, employ a low-sensitivity type Floatless Level Controller. Standard electrodes are made of stainless steel and usable in purified water, sea water, sewage, acid except acetic acid, sulfuric acid, etc. In this case the relay does not de-energize until the 61f-gp-m2 level falls below the low-level probe.

A low voltage is applied between these probes and the earth probe or tank, if it is electrically conductive. Make sure that the terminal cover is installed before using the product. Lock nut Electrode 2.

Usually, electrodes are used in a set of three: Data presented omrom Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. Use separator when connecting. Doing so causes malfunctions by getting vulnerable to induction noise.

This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Iron is more reactive than copper. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. Fully fit the electrode into the connecting nut attached to the electrode holder.


This is a temporal bone which had an implant electrode Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty.

Alarm control warning of abnormal or dangerously high or low levels. E1 Electrodes are in actual contact with the liquid.

The water provides a current between the earth probe and the high-level probe.

61F-GP-N2 – OMRON Industrial Automation

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. To convert millimeters into inches, multiply by 0.

Between electrode E1 and E3 Release resistance Approx. In the 61g-gp-n2 of product improvement, specifications are subject to change without notice. Ideal for use in tanks where temperature or pressure inside the tank is high, e. When the required length of the electrode is more than 1 m, use a separator at each joint of two electrodes so as to prevent the electrodes from contacting one another.

The output relay in the controller is energized when the water level reaches the high-level probe and de-energized when the water level falls below it. 61f-gpp-n2 a lock nut and a spring washer onto the electrode. Avoid use of the separators in dust-containing liquids.

When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. When using a noise filter, check the voltage and current and install it as close to the product as possible.

61F-GP-N2 – OMRON Industrial Automation

Make E3 at least 50 mm longer than E2. Special 3-pole holder of small size and light weight. Connect the short electrode to E1, the medium electrode to E2, and the long electrode to E3. For acids, alkalis and sea water, electrode holders may be as much as 1 meter apart to operate properly.


Omron 61F-GP-N2 Processor/Controller

Doing so may occasionally result in minor or moderate injury due to electric shock. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or 611f-gp-n2. Return of any Products by Buyer must be approved in writing by Omron before shipment.

Doing so can reduce some effects of noise. In sewage use, electrode holders must be installed 10 to 20 cm apart from one another. To convert grams into ounces, multiply by 0. Long distance for wiring may causes malfunctions because stray capacitance may influence operation, or abnormal surges or noise may run through electrode circuit s.

Omron 61F-GP-N2 Processor/Controller | eBay

Secure the connecting nut by tightening the lock nut and spring washer. Similarly, avoid using next to a high-capacity contactor which may impacts 611f-gp-n2 operation. Indication of liquid buildup due to filter blockages. Buyer shall take application responsibility in all cases. These are cut to length and inserted vertically into the liquid. Documents Flashcards Grammar checker.