Site Overlay

ASTM B117-07A PDF

The salt spray (or salt fog) test is a standardized and popular corrosion test method, used to ASTM B was the first internationally recognized salt spray standard, originally published in Other important relevant standards are. Designation: B – 07a Standard Practice for Operating Salt Spray (Fog) Apparatus1 This standard is issued under the?xed designation B. ASTM B Testing, also known as a Standard Practice for Operating Salt ASTM B Testing requires controls over many operational parameters such as: .

Author: Zulkikasa Kejar
Country: Mauritius
Language: English (Spanish)
Genre: Travel
Published (Last): 15 September 2017
Pages: 484
PDF File Size: 14.61 Mb
ePub File Size: 4.35 Mb
ISBN: 693-3-50401-873-8
Downloads: 28003
Price: Free* [*Free Regsitration Required]
Uploader: Digar

These acidified test solutions generally have a pH of 3. Your comments are invited b117-07w for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

After cleaning, rinse each panel with reagent grade water Type IV and dry see A superscript epsilon e indicates an editorial change since the last revision or reapproval. ISO standards by standard number. A number in asgm indicates the year of last reapproval. ASTM G85 is the most popular global test standard covering modified salt spray tests. The fallout rate should be measured for 16 hours and it must range from 1.

Is VLM only a distributor of corrosion test chambers? The cleaning method shall be optional depending on the nature of the surface and the contaminants.

The principle application of the salt spray test is therefore enabling quick comparisons to be made between actual and expected corrosion resistance. Bare metal shall not be used. How can I check whether my salt spray test chamber operates properly? Place bb117-07a panels in the proximity of the condensate collectors.

If these conditions are met, you can assume that your machine runs fine. Conditions in the Salt Spray Chamber Different coatings have different behavior in salt spray test and consequently, test duration will differ from one type of coating to another.

Chamber volumes vary from supplier to supplier. B In order to ensure that the proper salt concentration was achieved when mixing the solution, it is recommended that the solution be checked with either a salimeter hydrometer or speci?

  ERWIN RIEDEL ALLGEMEINE ANORGANISCHE CHEMIE PDF

SAL 3000-FL

This test can be used to test the relative resistance to corrosion of aluminium alloys when exposed to a changing climate of acetic acid salt spray, followed by air drying, followed by high humidity, all at an elevated temperature. Most commonly, the time taken for oxides to appear astj the samples under test is compared to expectations, to determine whether the test is passed or failed.

Specimens shall preferably be supported from the bottom or the side.

However, these testing standards neither provide information of testing periods for the coatings to be evaluated, nor the appearance of corrosion products in form of salts. Salt Spray Test Chambers.

SAL 400-FL

After cleaning, weigh each panel on an analytical balance to the nearest 1. The number of nozzles depends on type and capacity and is related to the area asm the test space. In any testing program, sufficient replicates should be included to establish the variability of the results. The first prerequisite for your test chamber to operate properly is that it is regularly serviced and well maintained. ISO gives the guidelines for proper measurement of corrosion satm for hot-dip galvanized specimens.

NOTE 13—If any of the atomized salt solution which has not contacted the test specimens is returned to the reservoir, it is advisable to record the concentration or speci?

salt spray test, ASTM B, corrosion tests

Thus, the level of the solution in the salt h117-07a must be maintained automatically to ensure uniform fog delivery during the test. Cleaning of Tested Specimens Testing periods range from a few hours e. The most commonly used type is made of plastic. Suitable apparatus which may be used is described in Appendix X1. Accessories for Corrosion Testing. The first climate cycle comprises a continuous indirect spray of neutral pH 6. The most common b17-07a for steel based materials is the Neutral Salt Spray test often abbreviated to NSS which reflects the fact that this type of test solution is prepared to a neutral pH of 6.

  ALODINE 1200S PDF

ASTM B – 07a Standard Practice for Operating Salt Spray (Fog) Apparatus

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? For this reason the salt spray test is most often deployed in a quality audit role, where, for example, it can be used to check the effectiveness of a production process, such as the surface coating of a metallic part.

In this connection it is well to point out that Practice B is not applicable to the study or testing of decorative chromium plate nickel-chromium on steel or on zinc-base die castings or of cadmium plate on steel. The company was founded in and from the very beginning it started working on innovative design concepts for test chambers.

Hot-dip galvanizing produces zinc carbonates when exposed to a natural environment, thus protecting the coating metal and reducing the corrosion rate.

The conditions of making the scratch shall be as de? Before the solution is atomized it shall be free of suspended solids Note 4. Current edition approved Dec. Salt Spray Test Chambers. This may be accomplished by placing the apparatus in a constant-temperature room, but may also be achieved by surrounding the basic chamber of a jacket containing water or air at a controlled temperature.

ASTM G85 astk A1 — Acetic Acid Salt Spray Test non-cyclic This test can be used to determine the relative resistance to corrosion of decorative chromium plating on steel and zinc based die casting when exposed to an acetic acid salt spray climate at an elevated temperature.

Options for corrosion chambers. Test specimens are placed in an enclosed chamber, and exposed to 1 of 2 possible changing climate cycles. Accessories for Corrosion Testing.