ASTM D – Air Permeability of Textile Fabrics . Reference: ASTM D – Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament . ASTM D/DM: Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns Made from Manufactured Organic-Base Fibers. This standard is issued under the fixed designation D ; the 1 These test methods are under the jurisdiction of ASTM Committee D13 on.
|Published (Last):||10 December 2018|
|PDF File Size:||17.16 Mb|
|ePub File Size:||8.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Specimen gripping Instron’s Solution: Width of Tire Cord Fabric. Extractable Matter in Yarns and Cords.
Significance and Use, Tensile Properties. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of asrm limitations prior to use.
Software for Series Systems. Combining values from the two systems may result in non-conformance with the standard. This standard may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications.
Contraction of Wet Yarns and Cords. CP Rated capacity 5 kN kgf, 1, lbf Suitable for testing a wide range of tire aztm, braided wire, tow and mono-filements. How can we help you? Bibliography of Tire Cord Test Methods. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! Bluehill LE for Basic Testing. Work-to-Break of Yarns and Cords. Email addresses can only contain letters, numbers and the following special characters: They may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications.
ASTM D885 Tire Cord Tensile Test
If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.
Next Checking to see if you are a returning visitor…. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part d85 the standard. Link to Astmm This link will always route to the current Active version of the standard. Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: Onsite Training At Your Facility.
Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. Breaking Toughness of Yarns and Cords. Link to Active This link will always route to the current Active version of the standard.
The result of this test is a determination of tensile strength of the cord being tested. They are designed with aztm and optional features that increase testing efficiency and improve the testing experience for the operator. This standard details the testing of fibers and cords made specifically for use in the manufacture of pneumatic tires. Subscribe to Our Newsletters. Description Literature Contact Us This standard details the testing of fibers and cords made specifically for use in the manufacture of pneumatic tires.
The test methods apply to nylon, polyester, rayon, and aramid yarns and tire cords twisted from such yarns and to fabrics made from such cords. It is important to review ASTM D to fully understand the test setup, procedure, and results requirements.
Elongation at Break of Conditioned Yarns and Cords. The values stated in either acceptable metric units or zstm units shall be regarded separately as standard.
ASTM D – Tire Cord and Yarn Grip
Count of Tire Cord Fabric. Email addresses must contain the symbol. Twist in Yarns and Cords. Significance and Use, General.
ASTM D Industrial Filament Yarns Made from Manufactured Organic-Based Fibers – Instron
Adhesion of Cord to Elastomers. The values expressed in each system may not be exact equivalents; therefore, each system must be used independently of each other, without combining values in any way.
Other materials with established test values may be used for this purpose.
It is recommended that any program of acceptance testing be preceded by an interlaboratory check in d8885 laboratory of the purchaser and the laboratory of the supplier on replicate asgm of the materials to be tested for each property or properties to be evaluated.