Site Overlay


Modular Fixture Design for BIW Lines Using Process Simulate® .. Tapping, Testing, Turning, Welding, Robotic Spot Welding, Robotic Painting. BIW WELDING FIXTURE UNIT BIW welding fixtures are used for holding the sheet metal or part assembly together in space while the components are. BIW Fixture Design solution: HRT provides service solutions with top quality for BIW Welding Fixtures in Automotive Industry. We provide complete BIW Fixture.

Author: Vudozil Kajigrel
Country: Egypt
Language: English (Spanish)
Genre: Technology
Published (Last): 22 September 2007
Pages: 449
PDF File Size: 8.56 Mb
ePub File Size: 5.47 Mb
ISBN: 502-3-14488-343-7
Downloads: 65843
Price: Free* [*Free Regsitration Required]
Uploader: Tauzahn

So, designing a fixture in this plane is often a complex process, considering the variations in coordinate systems and basic rules such as maintaining few elements in specific orientations.

Enter the email address you signed up with and we’ll email you a reset link. Usually two locating pins are enough to properly locate the body part on one plane.

Sheet Metal Fixtures

This is usually done with the datum surfaces that are reference for locating surface. The dimensions of datum surface are decided by selecting a necessary cross- section from the part drawing. Clamping device In every welding operation for body assembly, clamping of panel is an essential requirement.

One of the pins is round, and another one is diamond shaped. Rixtures clamp can be defined as a device for providing an invariant location with respect to an external loading system.

When a welding process welidng producing a load or moment on the body part, it is necessary that a sufficient clamping force must be exerted to withstand such actions. The generalized requirements of clamping device can be summarized as: The dimension from the panel to the eelding pin leading end straight area should be 5 mm. Help Center Find new research papers in: This configuration will allow easier loading of body part.


The surface of base should be flat smooth and the base should be rigid enough for easy welding and machining.

Designing a welding fixture is based on the location layout. Log In Sign Up. The end of each pin has a round or conical shape or is chamfered for the purpose of maintaining workability such as ease of loading and quality such as prevention of damage.

BIW Welding Fixture Design in Sector 6, Gurgaon | ID:

Locating surface is configured to receive panel for setting in a correct position and locating a body part from any surface such as flat, curved, or have an irregular contour. Remember me on this computer. In other words a clamp is a force-actuating mechanism of a fixture unit.

Fixture unit to hold the body parts securely and composed of following item: The shape of locating surface is a form of cross-section of panel. The fxitures between the locate hole in the panel or body part and the locating pin diameter should be 0.

BIW Welding Fixture | Varad Industries | Manufacturer in Bhosari, Pune | ID:

There is deformation of body assembly due to the welding process effect and resulting variation due to part dimensional variation, when you are designing a fixturse you should eliminate them and another objective is achieving body quality within the required tolerances, so you can achieve this purpose by planning location layout. The body part is constrained by a set of appropriately locating pin so total constraint by locating pin should be fully constrained at all times to prevent any movement.

  ASTM E1272 PDF

Skip to main content. Locating pins are available in numerous shapes and sizes in a design. It involves numbers of fixture units and due to the complexity and shape of the component geometry, the choice of elements as well as configuration of each unit tends to change from case to case.

Fixturrs forces exerted by the clamps hold a panel securely in the fixture against all other external forces.

BIW Welding Fixture Design

Click here to sign up. Location layout is the selection of the positions and numbers of locators and clamps for assembly of fixture components into a final configuration on a fixture base. The framework of the base is usually made of shape steel.

There are two configurations for position of locating pin: The taper lead angle is large, 60 degrees or less, for small-size body parts and manual operation, but it is frequently between10 and 30 degrees for large-size body parts that are difficult to handle. Load condition and configuration are not uniform, so it is impossible to set a base shape in general.

In most applications, locating surface devices locate a panel fixtuges its external flat surfaces and flat area, such as: