DS/ISO Accuracy (trueness and precision) of measurement methods and results – Part 4: Basic methods for estimating the trueness of a standard. ISO Accuracy (Trueness and Precision) of Measurement Methods and Results – Part 4: Basic Methods for the Determination of the Trueness of a. Buy DS ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 4: BASIC METHODS FOR.
|Published (Last):||15 January 2005|
|PDF File Size:||20.53 Mb|
|ePub File Size:||19.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
Alternative methods for the determination of the precision of a standard measurement method. If the reproducibility of the measurement method is poor, then it will not be practical to achieve a high degree of certainty in the estimate of 5725–4 bias.
BS ISO 5725-4:1994
The k values figure B-7 show that laboratories Related international standards ISO In chemical anal- ysis, problems may arise from, for example, insufficient control of temperature, moisture, pres- ence of contaminants, etc.
Utilization of trueness data Refer to clause 7 of IS0 Comparison of the trueness of two measurement methods is considered in IS0 Relevant International Standards on sample division should be consulted. IAccuracy trueness and precision of measurement methods and results – Part 1: IS0 l should be read in conjunction with all other parts of IS0including this part, because it gives the underlying definitions and general principles.
Exactitude justesse et fidelite des resultats et methodes de mesure. The variation of the estimate of the bias of the measurement method is due to the variation in the results of the measurement process and is expressed by its standard deviation computed as in the case of known precision values, or siJzT-yF .
Accuracy trueness and precision of measurement methods and results. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. The results of this computation are summarized in table B. Thus results from each kso can be considered as replicates under repeatability conditions.
Each laboratory re- ceived two randomly selected bottles of test sample for each level and performed duplicate analyses on each bottle.
ISO Accuracy of measurement methods and results-Part 2 Basic method – MBA智库文档
Apart from the restriction to a single laboratory. Please download Chrome or Firefox or view our browser tips. Basic method for the determination of repeatability and re- producibility of a standard measurement method – Part 3: Bias sio arise, for example, in chemical analysis if the measurement method fails to extract all of an element, or if the presence of one element interferes with the determination of another.
Basic 572-54 for the determination of repeatability and reproducibility of a standard measurement method.
In this report the following information shall be given: Intermediate measures of the precision of a standard measurement method. Alternative methods for the determi- nation of the precision of a standard measure- ment method.
When gR is larger than T. One laboratory re- sult was identified as a straggler; it originated from the same laboratory Lab.
The repeatability and the reproducibility standard de- viations were then computed excluding those 575-4 that were discarded. The differences are a there is an additional requirement to use an ac- cepted 55725-4 value, and b the number of participating laboratories and the number of test results shall also satisfy the re- quirements given in 4.
What action is to be taken concerning its publication? In order for the results of an experiment to be ios to detect with a high probability see annex Cl a prede- termined magnitude of bias, the minimum number of laboratories, p, and test results, n, shall satisfy the following equation: It was therefore decided to discard the results from laboratory 10 completely; it should be the object of special attention, and the matter should be resolved.
Unless otherwise stated, a is assumed to be 0, If the repeatability standard deviation, or, of the stan- dard measurement method is known, the estimate s, can be assessed by the following procedure.
Enoval – References
Alternative methods for the determination of the precision of a standard measurement method – Part 6: Unless otherwise stated, a is assumed to be 0. In particular, if outlying values are de- tected, all necessary steps shall be taken to investi- gate the reasons why they have been obtained, including re-appraisal of the suitability of the accepted reference value. The analytical results are listed in tableB. Accept and continue Learn more about the is we use and how to change your settings.
Intermediate measures of the precision of a standard measurement method – Part 4: Analysis of the results showed that the between- 57225-4 variation was indeed insignificant; the sample was considered to be homogeneous.
There again, appropriate action should be taken by investigating these laboratories, or, if necessary, by tightening the protocol of isoo measurement method. As a result the experiment may have to be repeated to yield the expected preci- sion values. Accuracy trueness and precision of measurement methods and results — Part 4: The uncertainty in the estimate of the laboratory bias depends on the repeatability of the measurement method and on the number of test results obtained.
Genauigkeit Richtigkeit und Praezision von Messverfahren und Messergebnissen. Basic methods for the determination of the trueness of a standard measurement method – Part 5: Outliers and stragglers Level Lab.